Premium 3600 Thin Set MSDS
I – PRODUCT IDENTIFICATION
MANUFACTURER:
MICRO MILLING LIMITED
Caxton Bay P.O. Box 4235, Plaisance Park Industrial Estate,
Pointe-a-Pierre,
Trinidad & Tobago, W.I.
Telephone #: 1(868) 659-4060
Generic Identity: Latex Modified Portland Cement Based Thin Set
Product Name: Micro Milling Premium 3600 Thin Set.
_________________________________________________________________________________________________
II – INGREDIENTS & HAZARDOUS COMPONENTS
Ingredient Name CAS Number Percent Exposure Limits
Crystalline Silica 14808-60-7 40-55 0.05mg/m³ (ACGIH)
Portland Cement 65997-15-1 35-45 10mg/m³ (ACGIH)
Latex Polymer n/a 3-8 n/a
OSHA PEL: Exposure to airborne crystalline silica shall not exceed an 8-hour time-weighted average (TWA) limit as
stated in 29 CFR 1910.1000 Table Z-3, Air Contaminants, specifically: 10 mg/m3 %SiO2+2
_________________________________________________________________________________________________
III – PHYSICAL DATA
Initial Boiling Point: N/A.
Vapour Pressure: N/A.
Vapour Density (Air=1.0): N/A.
Specific Gravity: 2.2 -2.3.
Percent Volatiles: 0.00%
________________________________________________________________________________________________
IV – FIRE AND EXPLOSION HAZARD DATA
Flash Point: N/A.
Explosive Limit (Product): N/A.
Extinguishing Media: None to avoid.
Special Fire Fighting Procedures: None.
Unusual Fire & Explosion Hazards: None.
_________________________________________________________________________________________________
2 | Page
_________________________________________________________________________________________________
V – HEALTH HAZARD DATA
Eye Contact: Crystalline silica (quartz) may cause abrasion of the cornea.
Skin Contact: Wet compound can dry the skin and cause caustic burns.
Ingestion: No adverse effects expected for incidental ingestion.
Inhalation: Air borne particulate matter may cause irritability of nasal passages, sneezing,
FIRST AID:
Eye Contact: Wash eyes immediately and repeatedly with water and seek prompt medical attention.
Skin Contact: Wash exposed skin with soap and water immediately.
Ingestion: If ingested, seek immediate medical attention. Drink water.
Inhalation: No first aid is necessary since the adverse health effects associated with exposure to crystalline silica (quartz)
result from chronic exposures. If there is a gross inhalation of crystalline silica (quartz), remove the person immediately to
fresh air, give artificial respiration as needed, seek medical attention as needed.
Chronic Effects: The adverse health effects – silicosis, lung cancer, scleroderma, tuberculosis, and nephrotoxicity – are
chronic effects.
CARCINOGENICITY:
NTP – Yes IARC – Yes OSHA – Yes
Crystalline Silica – IARC Group Agent 1
_________________________________________________________________________________________________
VI – REACTIVITY DATA
Stability: Stable
Incompatibility: (Materials to Avoid): Contact with powerful oxidizing agents such as fluorine, chlorine, tri-fluoride, and
oxygen di-fluoride may cause fires.
Hazardous Decomposition: None
Hazardous Polymerisation: None
Conditions to Avoid: Avoid contact with water or moisture during storage. Once packaging is opened contents should be
used as quickly as possible. Close bags after use to prevent the absorption of moisture and/or contaminants.
_________________________________________________________________________________________________
VII – SPILL OR LEAK PROCEDURES
Steps to be taken in case material is released or spilled:
Use Appropriate Respiratory Protection. Limit dust with water spray. Promptly clean by scoop or vacuum. Provide
ventilation. If spilled when already mixed with water, contain by dyking with inert absorbent materials and place in an
appropriate container for waste or disposal.
Refer to State and Local Regulations for handling solid waste
____________________________________________________________________________
VIII – PROTECTIVE EQUIPMENT
Ventilation: Open all available windows and entrances to ensure good ventilation
Respirator Protection: Occupational Safety & Health approved respirator
Protective Gloves: Leather or rubber gloves for skin and hands
Eye Protection: Wear glasses or protective goggles to avoid splashed droplets.
Always wash hands thoroughly with soap and water after handling product.
______________________________________________________________________________________________
IX – SPECIAL PRECAUTIONS
Use only in applications as stated on the label. Do not take internally. Close container after each use. Avoid skin and eye
contact.
3 | Page
Ventilation with fresh air, including open doors and windows should be observed during any flooring installation. Operate
HVAC systems at 100% fresh air intake before, during and after installation to eliminate lingering odors or particulate
matter.
The information accumulated herein is believed to be accurate but is not warranted to be, whether originating with the
company or not. Recipients are advised to confirm in advance of need that the information is current, applicable and
suitable to their circumstances.
Keep product out of the Reach of Children.
_________________________________________________________________________________________________
N/A=”Not Applicable” N/E=”Not Established”
MICRO MILLING LIMITED assumes no responsibility for personal injury or property damage to vendees, users, or third
parties caused by the material. Such vendees or users assume all risks associated with the use of the material.
Reviews
There are no reviews yet.